Today in Aviation History – Jimmy Doolittle Wins The Schneider Trophy

Lieutenant James H. Doolittle, Air Service, United States Army, with the Curtiss R3C-2 Schneider Trophy winner, 1925. (U.S. Air Force)


by Bryan R. Swopes of This Day in Aviation

On October 26, 1925, Lieutenant James Harold Doolittle, Air Service, United States Army, won the Coupe d’Aviation Maritime Jacques Schneider (commonly called the Schneider Trophy) when he placed first flying his Curtiss R3C-2 floatplane over a 217-mile (349 kilometers) course near Bay Shores on Chesapeake Bay, Maryland.

Doolittle’s average speed for the seven laps around the triangular racecourse was 232.57 miles per hour (374.29 kilometers per hour). The second-place airplane, a Gloster-Napier III flown by Captain Hubert Broad, averaged 199.16 miles per hour (320.52 kilometers per hour).

Doolittle also set two Fédération Aéronautique Internationale (FAI) world records during the race: World Record for Speed Over 100 Kilometers, with an average speed of 377.83 kilometers per hour (234.77 miles per hour);¹ World Record for Speed Over 200 Kilometers, 377.16 kilometers per hour (234.36 miles per hour).² On the following day, Doolittle set a third FAI record: World Record for Speed Over a 3 Kilometer Course, 395.5 kilometers per hour (245.75 miles per hour).³

Lieutenant James H. Doolittle left and Lieutenant Cyrus Bettis with the Curtiss R3C 2. NARA 31758AC
Lieutenant James H. Doolittle (left) and Lieutenant Cyrus Bettis with the Curtiss R3C-2. (NARA 31758AC

A contemporary news article commented on Jimmy Doolittle’s performance:

. . . according to reports Lieut. Doolittle’s cornering was superb and must have been to a great extent responsible for the excellent performance. Reports from America—coming, it is thought, from a reliable source—indicate that one particular engine out of the 12 built for the Pulitzer and Schneider Trophy races proved exceptionally good, as will often happen in a batch of engines, and it is believed that this engine was fitted in Doolittle’s Curtiss-Army Racer. This fact, taken in conjunction with the masterly handling of the machine, would seem to account for the wholly unexpected average speed maintained, which was, of course, far and away ahead of the speeds of the British and Italian competitors.

—FLIGHT, The Aircraft Engineer & Airships, No. 879 (No. 44, Vol. XVII.) October 29, 1923, at Page 703

The triangular Schneider race course stretched from Bay Shore Park to Gibson Island to the south and across Chesapeake Bay to Huntingfield Point
“The triangular Schneider race course stretched from Bay Shore Park to Gibson Island to the south and across Chesapeake Bay to Huntingfield Point. Contestants had to fly the 50-kilometer (31-mile) course seven times.” Smithsonian National Air and Space Museum

The R3C-2 was a single-engine, single-seat, single-bay biplane, equipped with pontoons for taking off and landing on water. It was built especially for air racing. Two R3Cs were built for the United States Navy and one for the Army. (The Army aircraft is identified by a Navy Bureau of Aeronautics serial number (“Bu. No.”) A-7054. It does not seem to have been assigned an Air Service serial number.) The airplane and its V-1400 engine were both built by the Curtiss Aeroplane and Motor Company, which had been founded by Glenn Hammond Curtiss. The R3C-2 was converted from the R3C-1, the landplane configuration which had been flown by Lieutenant Cyrus Bettis, AS, the USA, to win the Pulitzer Trophy Race just two weeks earlier.

The RC3-2 is 22 feet long (6.706 meters), an increase of 2 feet, 3.5 inches (0.698 meters) over the R3C-1 configuration, resulting from the replacement of the fixed wheeled landing gear with the single-step pontoons. The upper wingspan is 22 feet (6.706 meters), with a chord of 4 feet, 8¼ inches (1.429 meters). The lower wingspan is 20 feet (6.096 meters) with a chord of 3 feet, 3¾ inches (1.010 meters). Weight empty was 2,135 pounds (968 kilograms) and maximum takeoff weight was 2,738 pounds (1,242 kilograms).

Curtiss R3C 2 Racer at the National Air and Space Museum
The Curtiss R3C-2 Racer on display at the National Air and Space Museum. (Photo by Eric Long, National Air and Space Museum, Smithsonian Institution)

Constructed of wood, the fuselage has four ash longerons and seven birch vertical bulkheads. The framework is covered with two layers of 2-inch (51 millimeters) wide, 3/32-inch (2.38 millimeter) thick spruce strips. These were placed on a 45° diagonal from the fuselage horizontal centerline, with the second layer at 90° to the first. These veneer strips were glued and tacked to the frame. The fuselage was then covered with doped fabric. The wings and tail surfaces are also of wood, with spruce ribs and a covering of spruce strips.

The single-bay wings are wire braced and contain surface radiators made of thin brass sheeting. The radiators contained 12 gallons (45.4 liters) of water, circulating at a rate of 75 gallons (283.9 liters) per minute. By using surface radiators to cool the engine, aerodynamic drag was reduced.

The Curtiss V-1400 engine was developed from the earlier Curtiss D-12. It was a water-cooled, normally aspirated, 1,399.91-cubic-inch-displacement (22.940 liters), dual overhead cam (DOHC) 60° V-12, with a compression ratio of 5.5:1. The V-1400 was rated at 510 horsepower at 2,100 r.p.m., and could produce 619 horsepower at 2,500 r.p.m. It was a direct-drive engine and turned a two-bladed duralumin fixed-pitch propeller with a diameter of 7 feet, 8 inches (2.337 meters). The propeller was designed by Sylvanus Albert Reed, Ph.D. The V-1400 engine weighed 660 pounds (299 kilograms). The R3C-2 had a fuel capacity of 27 gallons (102 liters). Its range was 290 miles (467 kilometers).

Schneider Trophy 2006 2
The Coupe d’Aviation Maritime Jacques Schneider at the Science Museum, London. (Wikipedia, edit by Eric Menneteau)

Jimmy Doolittle was one of America’s foremost pioneering aviators. He set many records, won air races, tested and developed new flying equipment and techniques. He was a highly-educated military officer, having earned his Bachelor of Arts from the University of California Berkeley School of Mines, and M.S and D.Sc. degrees in Aeronautical Engineering from the Massachusetts Institute of Technology. During World War II, Colonel Doolittle planned and led the famous Halsey-Doolittle Raid against Japan, 18 April 1942, for which he was awarded the Medal of Honor. As a brigadier general, he commanded the 12th Air Force in North Africa. Promoted to major general, he was given command of the 15th Air Force in the Mediterranean Theater and commanded 8th Air Force as a lieutenant general, 1943–1945. After the war, Lieutenant General Doolittle was placed on the inactive list. On April 4, 1985, the U.S. Congress advanced him to full general on the Air Force retired list. In a later ceremony, President Reagan and Senator Goldwater pinned on his four-star insignia, making him the first person in Air Force Reserve history to wear four stars. Jimmy Doolittle died on September 27th, 1993.

¹ FAI Record File Number 11866

² FAI Record File Number 11867

³ FAI Record File Number 11868

 

For more aviation anniversaries please visit www.thisdayinaviation.com

This Day In Aviation Banner

Moreno-Aguiari

Born in Milan, Italy, Moreno moved to the U.S. in 1999 to pursue a career as a commercial pilot. His aviation passion began early, inspired by his uncle, an F-104 Starfighter Crew Chief, and his father, a military traffic controller. Childhood adventures included camping outside military bases and watching planes at Aeroporto Linate. In 1999, he relocated to Atlanta, Georgia, to obtain his commercial pilot license, a move that became permanent. With 24 years in the U.S., he now flies full-time for a Part 91 business aviation company in Atlanta. He is actively involved with the Commemorative Air Force, the D-Day Squadron, and other aviation organizations. He enjoys life with his supportive wife and three wonderful children.

Array
About Moreno Aguiari 3374 Articles
Born in Milan, Italy, Moreno moved to the U.S. in 1999 to pursue a career as a commercial pilot. His aviation passion began early, inspired by his uncle, an F-104 Starfighter Crew Chief, and his father, a military traffic controller. Childhood adventures included camping outside military bases and watching planes at Aeroporto Linate. In 1999, he relocated to Atlanta, Georgia, to obtain his commercial pilot license, a move that became permanent. With 24 years in the U.S., he now flies full-time for a Part 91 business aviation company in Atlanta. He is actively involved with the Commemorative Air Force, the D-Day Squadron, and other aviation organizations. He enjoys life with his supportive wife and three wonderful children.

Be the first to comment

Graphic Design, Branding and Aviation Art

Leave a Reply

Your email address will not be published.


*